G-shock AWG-M100 Bedienungsanleitung PDF herunterladen (Seite 9)

Operation Guide 5230

E-89

The current time setting changes after I set it manually.■

You may have the watch conﬁ gured for Auto Receive of the time calibration signal

(page E-28), which will cause the time to be adjusted automatically according to

your currently selected Home City. If this results in the wrong time setting, check

your Home City setting and correct it, if necessary (page E-42).

The current time setting is off by one hour.■

Possible Cause Remedy Page

Signal reception on a day for switching

between standard time/daylight saving

time (DST) may have failed for some

reason.

Perform the operation under “To get

ready for a receive operation”.

The time setting will be adjusted

automatically as soon as signal

reception is successful.

E-26

If you are unable to receive the time

calibration signal, change the standard

time/daylight saving time (DST) setting

manually.

E-45

E-88

The watch can’t receive a time calibration signal. The RCVD indicator does ■

not appear.

Possible Cause Remedy Page

You are wearing or moving the watch,

or performing a button operation

during the signal receive operation.

The watch is in an area with poor x

reception conditions.

Keep the watch in an area where

reception conditions are good while

the signal receive operation is being

performed.

E-26

You are in an area where signal

reception is not possible for some

reason.

See “Approximate Reception Ranges”. E-23

The calibration signal is not being

transmitted for some reason.

Check the website of the organization x

that maintains the time calibration

signal in your area for information

about its down times.

Try again later. x

–

E-87

Charging

The watch does not resume operation after I expose it to light.■

This can happen after the power level drops to Level 5 (page E-15). Continue

exposing the watch to light until the battery power indicator shows H or M.

Time Calibration Signal

The information in this section applies only when LIS, LON, MAD, PAR, ROM,

BER, STO, ATH, MOW, HKG, BJS, HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI,

NYC, YHZ, YYT, SEL, or TYO is selected at the Home City. You need to adjust the

current time manually when any other city is selected as the Home City.

E-86

The hands are off.■

This could indicate that the watch has been exposed to magnetism or strong

impact, which has caused problems with proper hand alignment. Adjust the watch’s

hand home position alignment (page E-75).

The analog hands are not indicating the correct time.■

If the HANDS indicator is displayed on the right digital dial, it means that the analog

hands have been moved for easier viewing of the digital dials. Hold down C for

about four seconds to return to the Timekeeping Mode.

World Time Mode

The time for my World Time City is off in the World Time Mode.■

This could be due to incorrect switching between standard time and daylight saving

time. See “To specify standard time or daylight saving time (DST) for a city” (page

E-54) for more information.

E-85

Troubleshooting

Time Setting

See “Radio Controlled Atomic Timekeeping” (page E-21) for information about

adjusting the time setting according to a time calibration signal.

The current time setting is off by hours.■

Your Home City setting may be wrong (page E-42). Check your Home City setting

and correct it, if necessary.

The current time setting is off by one hour.■

If you are using the watch in an area where time calibration signal reception is

possible, see “To conﬁ gure Home City settings” (page E-42).

If you are using in the watch in an area where time calibration signal reception is not

possible, you may need to change your Home City’s standard time/daylight saving

time (DST) setting manually. Use the procedure under “To change the current time

and date settings manually” (page E-48) to change the standard time/daylight

saving time (DST) setting.

E-84

After all of settings are the way you want, press 4. A to exit the setting mode.

Exiting a setting mode will normally cause the hands to return to regular x

timekeeping automatically. However, if you manually move the hands (page

E-79) and then enter a setting mode, they will not return to regular timekeeping

automatically when you exit the setting mode. In this case, you will need to

return the hands to their normal positions manually (page E-80).

E-83

To turn Power Saving on and off

In the Timekeeping Mode, hold down 1. A for about two

seconds until ADJ appears in the right digital dial.

When you release A, the city code and city name will

scroll across the right digital dial. This is the setting

mode.

Whenever you enter a setting mode, the analog hands

will automatically move to positions that allow easier

viewing of the digital dials.

Use 2. C to cycle through the settings in the right digital dial unit the current power

saving setting (PSON or PSOF) is displayed.

See the sequence in step 2 of the procedure under “To change the current time

and date settings manually” (page E-48) for information about how to scroll

between settings.

Press 3. D to toggle Power Saving on (PSON) and off (PSOF).

Power saving on indicator

E-82

Use 2. C to cycle through settings in the right digital dial until the current button

operation tone (MUTE or KEY

) is displayed.

See the sequence in step 2 of the procedure under “To change the current time x

and date settings manually” (page E-48) for information about how to scroll

between settings.

Press 3. D to toggle the button operation tone on (KEY

) and off (MUTE).

After all of the settings are the way you want, press 4. A to exit the setting mode.

Exiting a setting mode will normally cause the hands to return to regular

timekeeping automatically. However, if you manually move the hands (page

E-79) and then enter a setting mode, they will not return to regular timekeeping

automatically when you exit the setting mode. In this case, you will need to

return the hands to their normal positions manually (page E-80).

Note

The mute indicator is displayed in all modes when the button operation tone is

turned off.

E-81

Other Settings

The button operation tone sounds any time you press one of the watch’s buttons.

You can turn the button operation tone on or off as desired.

Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and

Countdown Timer Mode alarm all operate normally.

To turn the button operation tone on and off

In the Timekeeping Mode, hold down 1. A for about two

seconds until ADJ appears in the right digital dial.

When you release A, the city code and city name will

scroll across the right digital dial. This is the setting

mode.

Whenever you enter a setting mode, the analog hands

will automatically move to positions that allow easier

viewing of the digital dials.

Mute indicator

E-80

To return the hands to their normal positions

Hold down C for about two seconds until HAND appears.

Note

The hands will also return to their normal positions if you do not perform any

operation for about one hour.

The hands also will move away from the digital dial automatically whenever you

enter a setting mode in the Timekeeping Mode, Timer Mode, or Alarm Mode.

Time calibration signal reception is disabled while the hands are in positions to

allow easier viewing of the digital dials (page E-79).

Hold down x C for about four seconds to return the hands to their normal positions

and switch to the Timekeeping Mode.

1 2 3 4 5 6 7 8 9 10

Operation Guide 5230 1

Kommentare zu diesen Handbüchern

Keine Kommentare

G-shock AWG-M100 Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Uhr G-shock AWG-M100