G-shock AWG-M100 Bedienungsanleitung PDF herunterladen (Seite 4)

Operation Guide 5230

E-39

Countdown Timer Mode

Alarm ModeStopwatch Mode

E-38

Selecting a Mode

The illustration below shows which buttons you need to press to navigate between

modes.

To return to the Timekeeping Mode from any other mode, hold down

x C for at

least four seconds.

Timekeeping Mode World Time Mode

C C

E-37

Mode Reference Guide

Your watch has “ﬁ ve modes”. The mode you should select depends on what you

want to do.

To do this: Enter this mode: See:

View the current date in the Home City x

Conﬁ gure Home City and daylight saving time (DST) x

settings

Conﬁ gure time and date settings manually x

Perform a time calibration receive operation x

Check whether the last receive operation was successful x

Switch between 12-hour and 24-hour timekeeping x

Display an alarm countdown x

Timekeeping Mode E-41

View the current time in one of 48 cities (31 time zones)

around the globe

World Time Mode E-53

Use the stopwatch to measure elapsed time Stopwatch Mode E-57

Use the countdown timer Countdown Timer Mode E-60

Set an alarm time Alarm Mode E-63

E-36

The receive operation is disabled under any of the following conditions. x

While power is at Level 3 ( − L) or lower (page E-15)

While the watch is in the power recovery mode (page E-17)

−

When the watch is in the function sleep state (“Power Saving”, page E-19) −

While a countdown timer operation is in progress (page E-60) −

While the hands are in positions to allow easier viewing of the digital dials (page −

E-79)

A receive operation is cancelled if an alarm sounds while it is being performed. x

The Home City setting reverts to the initial default of x TYO (Tokyo) whenever the

battery power level drops to Level 5 or when you have the rechargeable battery

replaced. If this happens, change the Home City to the setting you want (page

E-42).

E-35

Press 4. A to exit the setting mode.

Exiting a setting mode will normally cause the hands to return to regular

timekeeping automatically. However, if you manually move the hands (page

E-79) and then enter a setting mode, they will not return to regular timekeeping

automatically when you exit the setting mode. In this case, you will need to

return the hands to their normal positions manually (page E-80).

Radio-controlled Atomic Timekeeping Precautions

Strong electrostatic charge can result in the wrong time setting.

Even if a receive operation is successful, certain conditions can cause the time x

setting to be off by up to one second.

The watch is designed to update the date and day of the week automatically for x

the period January 1, 2000 to December 31, 2099. Updating of the date by signal

reception will no longer be performed starting from January 1, 2100.

If you are in an area where signal reception is not possible, the watch keeps time

with the precision noted in “Speciﬁ cations” (page E-92).

E-34

To turn auto receive on and off

In the Timekeeping Mode, press 1. D (page E-41).

Hold down 2. A until the current auto receive setting (On

or OFF) and RCVD indicator start to ﬂ ash. This is the

setting mode.

Whenever you enter the setting mode, the analog

hands will automatically move to positions that allow

easier viewing of the digital dials.

Note that the watch will not enter the setting mode if

the currently selected Home City is one that does not

support time calibration reception.

Press 3. D to toggle between auto receive on (On) and

off (OFF).

RCVD indicator

On/Off status

E-33

To check the latest signal reception results

In the Timekeeping Mode, press D (page E-41).

When receive is successful, the left digital dial shows

the time and date that receive was successful. - : - -

indicates that none of the receive operations were

successful.

To return to the Timekeeping Mode, press x D.

Note

RCVD will not be displayed in the right digital dial if you

have adjusted the time or date setting manually since the

last receive operation.

E-32

Signal Level Indicator

During manual receive, the lower digital dial shows a

signal level indicator as shown below.

Weak

(Unstable)

Strong

(Stable)

As you watch the indicator, keep the watch in a location

that best maintains stable reception.

Even under optimum reception conditions, it can take

about 10 seconds for reception to stabilize.

Note that weather, the time of day, surroundings, and x

other factors all can affect reception.

Signal level indicator

E-31

If the current reception fails but a previous reception x

(within the last 24 hours) was successful, the right

digital dial will show RCVD and ERR. If only ERR

is displayed (without RCVD), it means that all of

the receive operations over the past 24 hours have

failed. The watch will return to the Timekeeping Mode

without changing the time setting if you press D or

if you do not perform any button operation for about

one or two minutes.

Note

To interrupt a receive operation and return to the

Timekeeping Mode, press any button.

If there was a previously

successful reception

Receive failed

E-30

If the receive operation is successful, the reception x

date and time appear in the left digital dial. The watch

will return to the Timekeeping Mode if you press D or

if you do not perform any button operation for about

one or two minutes.

Receive successful

1 2 3 4 5 6 7 8 9 10

Operation Guide 5230 1

Kommentare zu diesen Handbüchern

Keine Kommentare

G-shock AWG-M100 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Uhr G-shock AWG-M100