G-shock AWG-M100 Bedienungsanleitung PDF herunterladen (Seite 7)

Operation Guide 5230

E-69

The above operation turns on illumination regardless of the current auto light switch x

setting.

Illumination is disabled during time calibration signal reception. x

To change the illumination duration

In the Timekeeping Mode, hold down 1. A for about two seconds until ADJ

appears in the right digital dial.

When you release A, the city code and city name will scroll across the right

digital dial. This is the setting mode.

Whenever you enter a setting mode, the analog hands will automatically move to

positions that allow easier viewing of the digital dials.

Use 2. C to cycle through the settings in the right digital dial until the current

illumination duration (LT1 or LT3) is shown.

See the sequence in step 2 of the procedure under “To change the current time

and date settings manually” (page E-48) for information about how to scroll

through setting mode.

E-68

Illumination

The face of the watch is illuminated for easy reading in

the dark.

The watch’s auto light switch turns on illumination

automatically when you angle the watch towards your

face.

The auto light switch must be turned on (page E-72) for

it to operate.

To turn on illumination manually

Press B in any mode to illuminate the face of the watch.

You can use the procedure below to select either x

1.5 seconds or three seconds as the illumination

duration. When you press B, the face will remain

illuminated for about 1.5 seconds or three seconds,

depending on the current illumination duration setting.

E-67

Alarm Countdown

When the current time reaches one hour before an alarm

time setting, the alarm on/off indicator (in the lower digital

dial) will ﬂ ash and a countdown of the ﬁ nal 60 minutes

will be displayed in the right digital dial while the watch is

in the Timekeeping Mode.

Note

Pressing

x A while an alarm countdown is in progress

will display the day of the week in the right digital dial

for about two seconds. After that, the dial will return to

the countdown.

When you enter the Timekeeping Mode from another mode while an alarm

countdown is in progress, the day of the week will appear in the right digital dial for

two seconds. After that, the countdown will appear.

If an alarm countdown for another alarm starts while a previous alarm countdown is

already in progress, it will be displayed after the ongoing countdown reaches zero

and its alarm sounds.

Alarm ON/OFF indicator

Alarm Countdown

E-66

To turn an alarm and the Hourly Time Signal on and off

In the Alarm Mode, use 1. D to scroll through the alarm

indicators (AL1 to AL5, SIG) in the right digital dial until

the one you want is displayed.

When the alarm or the Hourly Time Signal you want is 2.

selected, press A to toggle it between on and off.

The alarm on indicator (when any alarm is on) and the

Hourly Time Signal on indicator (when the Hourly Time

Signal is on) are displayed in all modes.

To stop the alarm

Press any button.

Hourly Time Signal

on indicator

E-65

While a setting is ﬂ ashing, use 4. D (+) and B (–) to change it.

When setting the alarm time using the 12-hour format, take care to set the time x

correctly as a.m. (no indicator) or p.m. (PM indicator).

Press 5. A to exit the setting mode.

Exiting a setting mode will normally cause the hands to return to regular

timekeeping automatically. However, if you manually move the hands (page

E-79) and then enter a setting mode, they will not return to regular timekeeping

automatically when you exit the setting mode. In this case, you will need to

return the hands to their normal positions manually (page E-80).

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

E-64

To set an alarm time

In the Alarm Mode, use 1. D to scroll through the alarm

indicators (AL1 to AL5, SIG) in the right digital dial until

the one whose time you want to set is displayed.

AL1 AL3 AL5AL2 AL4 SIG

DDDDD

Hold down 2. A for about two seconds until the alarm time starts to ﬂ ash. This is

the setting mode.

Whenever you enter the setting mode, the analog hands will automatically move

to positions that allow easier viewing of the digital dials.

Press 3. C to move the ﬂ ashing between the hour and minute settings.

Alarm ON/OFF indicator

E-63

Using the Alarm

You can set ﬁ ve independent daily alarms. When a daily

alarm is turned on, an alarm tone will sound for about

10 seconds each day when the time in the Timekeeping

Mode reaches the preset alarm time. This is true even if

the watch is not in the Timekeeping Mode.

You can also turn on an Hourly Time Signal, which will

cause the watch to beep twice every hour on the hour.

To enter the Alarm Mode

Use C to select the Alarm Mode as shown on page

E-39.

The right digital dial will show

x ALM for about one

second and then the indictor for the currently selected

alarm (AL1 through AL5, or SIG) will appear.

When you enter the Alarm Mode, the data you were

viewing when you last exited the mode appears ﬁ rst.

Alarm number

Alarm time (Hour : Minutes)

E-62

To perform a countdown timer operation

D D D A

Start Stop (Restart) (Stop) Reset

Before starting a countdown timer operation, check to make sure that a x

countdown operation is not in progress (indicated by the seconds counting down).

If it is, press D to stop it and then A to reset to the countdown start time.

An alarm sounds for 10 seconds when the end of the countdown is reached. This

alarm will sound in all modes. The countdown time is reset to its starting value

automatically when the alarm sounds.

To stop the alarm

Press any button.

E-61

Hold down 2. A until the minute setting of the current countdown start time starts

to ﬂ ash. This is the setting mode.

Whenever you enter a setting mode, the analog hands will automatically move to

positions that allow easier viewing of the digital dials.

Press 3. C to move the ﬂ ashing between the minute and second settings.

Use 4. D (+) and B (–) to change the ﬂ ashing item.

To set the starting value of the countdown time to 100 minutes, set

x 00'00".

Press 5. A to exit the setting mode.

Exiting a setting mode will normally cause the hands to return to regular

timekeeping automatically. However, if you manually move the hands (page

E-79) and then enter a setting mode, they will not return to regular timekeeping

automatically when you exit the setting mode. In this case, you will need to

return the hands to their normal positions manually (page E-80).

E-60

Using the Countdown Timer

The countdown timer can be set within a range of one minute to 100 minutes. An

alarm sounds when the countdown reaches zero.

To enter the Countdown Timer Mode

Use C to select the Countdown Timer Mode (TMR) as

shown on page E-39.

To specify the countdown start time

Enter the Countdown Timer Mode.1.

If a countdown is in progress (indicated by the

seconds counting down in the left digital dial), press

D to stop it and then press A to reset to the current

countdown start time.

If a countdown is paused, press

x A to reset to the

current countdown start time.

Countdown time

(Minutes, seconds)

1 2 3 4 5 6 7 8 9 10

Operation Guide 5230 1

Kommentare zu diesen Handbüchern

Keine Kommentare

G-shock AWG-M100 Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Uhr G-shock AWG-M100